Microsun light repair

[bodger]

I'm a fan of bright, high-quality light for reading and crafts, so I figured I'd try the fancy Microsun lamps. These are 68W metal halide lamps, and provide 5300-6000 lumens with a CRI of 72-90, depending on who you believe. The lamps are expensive, but nicely made. I bought two of 'em, a floor lamp (for crafts) and a table lamp (for reading). They work well, and several people admired the quality of light they produce. However, after two years of fairly light use, the reading lamp started to flicker and then died. I tried swapping bulbs, but the problem remained with the lamp.

People who know me will not be surprised by my next move. The ballast (called a "gear pack" by the seller) is clearly marked "DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE." maugorn and others might remember me reciting the litany "Do not open, no user serviceable parts inside, pilot lamps soldered in place, danger high voltage, warranty void if opened, etc." as I tore into things.

Well, I found out some things. The manufacturer claims that you can't just make your own lamp by buying a gear pack, because the gear pack doesn't include "the transformer". I had initially believed there was a transformer tucked into the base of the lamp, as the lamp was sufficiently large and heavy. But there isn't one. The AC leads go straight to the gear pack. You could easily retrofit any ordinary threaded-tube lamp by buying a $60 gear pack and screwing it on top.

The ballast is patented. This means I can download the schematic. It's not quite the same as the one used in the lamp, but it's pretty close. It's just a current-regulated DC power supply with a transformer-coupled starting pulse network, run off a voltage doubler. Armed with that info, and the failure mode, I deduced that it isn't the starting circuitry (the lamp failed when it was already started), and it probably isn't the current regulator (those generally work right or not at all). That leaves the voltage doubler. Not much to it, an inrush current limiter, a pair of diodes, and two big electrolytic capacitors. And electrolytic capacitors are famous for drying out and failing. So I read the specs off 'em, measured the relevant dimensions, and found equivalent units on Digikey. The inrush limiter was a house-numbered part, but a little research convinced me that it was a 10Ω, 1.7A unit or thereabouts, and such things aren't critical (it's just there to make sure that the discharged capacitors don't pull too much current when first turned on). I chose a similar unit that would physically fit and ordered it too.

While I waited for the parts to show up in the mail, I considered my other options. These days, low-wattage metal halide bulbs aren't too hard to find, and ballasts can be had from Fulham (a manufacturer whose products I like) and cheaper manufacturers. If it dies again, I can always re-use the lamp body and nice, high-temperature ceramic socket with a 70W (or more!) metal halide bulb and ballast.

Comments

[roadstir]

Bodger,

Bodger,

A couple of questions on your Microsun.

Can I run more than a 70w bulb in the desklamp?
Any bulb numbers that you can recommend? I know it has to be protected, but there are so many 70w bulbs out there... And does it have to be frosted?

Many thanks

[bodger]

You're pretty much stuck with 68 or 70 watts, unless you replace the ballast with something else. Most ordinary 70W bulbs wouldn't work well, as the Microsun operates the lamp on DC, whereas most metal halide bulbs are designed for AC operation. Again, if you replace the ballast, you can go for more common bulbs and higher wattage. If you're curious, the Microsun bulb is a Venture Lighting product, part number 69000.

[roadstir]

Many thanks for the advice and quick reply, Bodger!

From: bodger - DW Comment [mailto:dw_null@dreamwidth.org] Sent: Wednesday, May 6, 2015 11:10 PM To: dlydiard@verizon.net Subject: Reply to your comment. [ bodger - 11977 ]

bodger: xkcd android girlfriend arc weld cherry stem (Default) http://v.dreamwidth.org/341383/358375

bodger http://bodger.dreamwidth.org/profile replied to a comment you left in a Dreamwidth entry http://bodger.dreamwidth.org/11977.html "Microsun light repair". The comment they replied to was:

Bodger,

Bodger,

A couple of questions on your Microsun.

Can I run more than a 70w bulb in the desklamp? Any bulb numbers that you can recommend? I know it has to be protected, but there are so many 70w bulbs out there... And does it have to be frosted?

Many thanks

The reply was:

You're pretty much stuck with 68 or 70 watts, unless you replace the ballast with something else. Most ordinary 70W bulbs wouldn't work well, as the Microsun operates the lamp on DC, whereas most metal halide bulbs are designed for AC operation. Again, if you replace the ballast, you can go for more common bulbs and higher wattage. If you're curious, the Microsun bulb is a Venture Lighting product, part number 69000.

From here you can:

• Reply http://bodger.dreamwidth.org/11977.html?replyto=32201 at the webpage
• View all comments http://bodger.dreamwidth.org/11977.html#comments to this entry
• Go to the top of the thread <http://www.dreamwidth.org/go?redir_type=threadroot&amp;journal=bodger&amp;talkid=32> this comment is part of
• View the thread http://bodger.dreamwidth.org/11977.html?thread=32201#cmt32201 beginning with this comment

Reply to this comment by replying to this email. Replies will be formatted using Markdown syntax. Your comment must appear before all other text at the top of the reply email. Do not change the reply-to address. It uses a secret address to identify you. Reset the secret address http://www.dreamwidth.org/manage/emailpost if you've accidentally shared it with anyone else.